Anaerobic High-temperature Test Chamber
● Independent air circulating cooling device.
● Door seal strip with unique thermal insulation function.
● 2 sets of baffles with the maximum loading capacity of 45Kg.
● Self-diagnosis function alarm is used to identify and assist in solving the problem.
● Unique 3-layer chamber structure allows to cool down quickly.
● Unique pneumatic design ensures rapid cooling to reduce concentration and keep low oxygen concentration.
- specifications
- Refrigeration system
- Control system
- configuration
- accessories
型號Model | AT91-200 | AT216-200 | AT512-200 | AT1000-200 | AT91-300 | AT216-300 | AT512-300 | AT1000-300 | ||
內容積(L)Internal Volume (L) | 91 | 216 | 512 | 1000 | 91 | 216 | 512 | 1000 | ||
內箱尺寸(mm) Inner Dimension (mm) | W | 450 | 600 | 800 | 1000 | 450 | 600 | 800 | 1000 | |
H | 450 | 600 | 800 | 1000 | 450 | 600 | 800 | 1000 | ||
D | 450 | 600 | 800 | 1000 | 450 | 600 | 800 | 1000 | ||
外箱尺寸(mm) Outer Dimension (mm) | W | 1060 | 1210 | 1500 | 1730 | 1060 | 1210 | 1500 | 1730 | |
H | 820 | 970 | 1210 | 1480 | 820 | 970 | 1210 | 1480 | ||
D | 635 | 785 | 1065 | 1270 | 635 | 785 | 1065 | 1270 | ||
溫度范圍(℃)Temperature Range (℃) | (環溫+20~200)℃ (Ambient temperature +20~200)℃ | (環溫+20~300)℃ (Ambient temperature +20~300)℃ | ||||||||
升溫時間(min) Temperature Rise and Time(min) | (環溫+20~200)℃ (Ambient temperature +20~200)℃ | (環溫+20~300)℃ (Ambient temperature +20~300)℃ | ||||||||
≤40/min | ≤60/min | ≤70/min | ||||||||
箱內殘留氧氣濃度≤100ppm,耗高純度惰性氣體(如:N2)流量 Residual oxygen concentration ≤100ppm, consumption flow of high-purity inert gas (such as: N2) | ≤20L/min (≤50min fall ) | ≤50L/min (≤50min fall ) | ≤100L/min (≤50min fall ) | ≤200L/min (≤50min fall ) | ||||||
≤7L/min(濃度保持) ≤7L/min (concentration maintaining) | ≤15L/min(濃度保持) ≤15L/min (concentration maintaining) | ≤30L/min(濃度保持) ≤30L/min (concentration maintaining) | ≤60L/min(濃度保持) ≤60L/min (concentration maintaining) | |||||||
調溫方式 Temperature Regulation Mode | 強制送風循環換熱方式+內部冷卻系統 Forced air circulation heat transfer mode & internal cooling system | |||||||||
使用環境Operating Environment | 溫度:(5~36)℃ 濕度:(30~85)%RH 氣壓:(86~106)kpa Temperature: (5~36)℃ Humidity: (30~85)%RH Pressure: (86~106) kPa | |||||||||
材料Material | 內箱Inner Chamber | 不銹鋼板 SUS304 Stainless steel sheet SS304 | ||||||||
外箱Outer Chamber | 雙面鍍鋅鋼板,表面處理后靜電噴塑處理 Two-sided galvanved plafe- with electrostatic powder coating | |||||||||
保溫Thermal Insulation | 纖維高溫棉 High-temperature fiber cotton | |||||||||
箱門密封條 Chamber Door Sealing Strip | 耐高溫密封條(不含硅) High temperature resistant sealing strip (exclusive of silicon) | |||||||||
執行器Actuator | 風機Fan | 加長軸風機 Extended shaft fan | ||||||||
風門Damper | 手動調節換氣+循環 Manual adjustment for ventilation & circulation | |||||||||
加熱器Heater | 進口鎳鉻合金電發熱絲 Imported nickel-chrome electric heater wire | |||||||||
控制器 系統 Controller System | 顯示屏+PLCTouch Screen & PLC | 7.0",800×480分辨率,混合輸出PLC 7.0", 800×480 resolution, mixed output PLC | ||||||||
運行方式Running Mode | 程式運行(輸入的溫度和濕度程序運行) Program runs in Auto mode ( An entered temperature & humidity program is run) | |||||||||
設定方式Setting Mode | 簡體中文+英文,觸摸輸入 Simplified Chinese & English, input by touch | |||||||||
顯示分辨率Display Resolution | 溫度:0.1℃,時間:s Temperature: 0.01℃, pressure: 0.01kPa, time: s | |||||||||
傳感器Sensor | PT100(鉑電阻) ,K型熱電偶 PT100 (platinum resistor),K-type thermocouple | |||||||||
控制方式Control Mode | 抗積分飽和PID+自整定 Anti-integral saturation PID & auto-tuning | |||||||||
通訊功能Communication Function | (選購功能)RS485,方便遠程和本地通訊監控,(需配監控軟件,RS485/RS232轉換器,需用到PC機COM,USB口各1個),同時最多可接16臺,線材最長700m (Optional) RS485 makes it convenient for remote and local communication monitoring (monitoring software is required; RS485/RS232 converter, one PC computer COM and one USB port are required). Meanwhile, maximum 16 sets can be connected, the maximum length of wire material is 700m. | |||||||||
附加功能Additional Function | 故障報警提示功能,上下限保護功能 Fault alarm prompt function, upper and lower limit protection function | |||||||||
電源(V)Power Supply(V) | 交流電壓380V±38V 頻率50Hz±0.5Hz 三相四線+接地保護 AC voltage 380V±38V Frequency 50Hz±0.5Hz 3-phase 4-wire & earthing protection | |||||||||
最大電流(A) Maximum Current (A) | 3 | 4 | 7.6 | 9.8 | 4.1 | 5.8 | 9.8 | 14.5 | ||
電源功率(kW)Power (kW) | 2 | 2.7 | 5 | 6.5 | 2.7 | 3.8 | 6.5 | 9.5 | ||
重量(kg)Weight (kg) | 120 | 160 | 280 | 460 | 120 | 160 | 280 | 460 | ||
標準配置Standard Configuration | 樣品架2套,腳輪4個,保險絲4個氧氣濃度分析儀1套,流量計3個,減壓閥2個,風機變速器1個 2 sets of sample holders, 4 casters, 4 fuses, 1 set of oxygen concentration analyzer, 3 flow meters, 2 pressure relief valve, 1 fan speed transmission | |||||||||
安全裝置Safety Device | 漏電開關,電機,相序,超溫等保護功能 Leakage switch, motor, phase sequence, over-temperature protection ,etc. | |||||||||
注:氮氣進氣壓力和空氣進氣壓力都為1kgf/cm2。 Note: Both the nitrogen inlet pressure and air inlet pressure are 1kgf/cm2. |
● Independent air circulating cooling device.
● Door seal strip with unique thermal insulation function.
● 2 sets of baffles with the maximum loading capacity of 45Kg.
● Self-diagnosis function alarm is used to identify and assist in solving the problem.
● Unique 3-layer chamber structure allows to cool down quickly.
● Unique pneumatic design ensures rapid cooling to reduce concentration and keep low oxygen concentration.
Topect touch-type temperature and humidity controller is specially developed by Topect for the industry of environmental equipment; it consists of touch screen, PLC, temperature module and humidity module, powerful in functions. The touch screen is equipped with visual editing software, PLC logic programme, extensible I&O port and extensible multi-point temperature; USB interface allows users to export data (time optional). Remote monitoring is realized through RS485 communication and PC connection.
●The controllers are developed independently by our company with high performance. Characterized by 65536 color 7’’, TFT true-color touch screen and 800×480 dot matrix, it ensures realistic effects and comfortable operation. In addition, the entire interface is concise and clear, convenient and reliable.
●Our controllers have powerful debugging protection function, fault alarm and troubleshooting description; extensible I&O port can be used to prepare different control programs according to requirement to realize different functions; they can be developed separately according to actual environment but can be controlled by computer intensively through software. The controller interface adopts consistent style, convenient for users’ operation.
●With PLC program control, this system has timed running & stop function and power failure protection function as well as better stability.
●It can be connected to a centralized monitoring software and supports communication protocol, convenient for users’ secondary development; multiple test chambers can be monitored remotely.
●Temperature and oxygen concentration recorder (fig.1)
●Communication interface and software for remote control and data transmission (figure 2)
●Oxygen concentration analyzer (fig.2)
●Metal filter
●Dry filter
●Special load-bearing sample holder
●Circulating fan with speed adjustable
●Non-standard customized equipment can meet users’ demands